Overhead Drive
Overview
The overhead drive is one of the most common methods used to drive the cutters used in ornamental turning. (Cutters would be held in either a cutting frame or a Drill Spindle.)
The benefits of using an overhead drive over a direct drive are :
- When the ornamental turner has a number of cutting or Drill Spindles, only one motor is needed for all of them, saving money for the craftsman.
- By having the motor separated from the cutting or Drill Spindle, there is a reduction in transfer of the motor's vibrations to the cutter.
- By having the motor further away from the craftsman :
- the motor's noise is further from the craftsman, and
- the craftsman has less obstruction to the visibility of his work.
Drive Motor
The motor to use for the overhead drive is the next thing to consider. It should be powerful enough to drive the cutter when cutting very hard woods, and turn it fast enough to make the cuts. But it can't be too fast or the belting will jump off the idler pulleys.
Generally, the guidelines recommended are :
- ½ horsepower
- variable speed
One motor which is commonly used is from Penn State Industries - the Variable Speed Midi Lathe Conversion Kit. Another is the Sherline Variable speed motor.
If you chose to repurpose a router for this use, be sure to put a speed controller on the power feed. Rockler sells one, item number 25278. These work by changing the frequency of the power. Be aware of these things if you incorporate this into your design:
- These motors were designed to operate at a certain speed, and changing that affects the power they can deliver. At too low a speed, they become ineffective.
- The cooling for these motors were designed for them running at a certain speed. If they run too slowly, the motor could overheat if used too long.
- Some speed controllers were designed for motors with brushes. I don't know what will happen if they are used with brushless motors.
Using a router is not recommended.
Cable Belting
A belt is needed for the overhead drive motor to drive the cutter.
I use round belting from McMaster-Carr, part number 59725K729. It is made from polyurethane rubber, is 1/8" diameter, and is orange (because I like the colour). It is sold by the foot.
Fred Armbruster recommends textured belting for his cutting frames. He recommends belting from Habasit which is available from McMaster-Carr. Look for textured round belting.
One argument made for textured belting s is that it doesn't slip as easily.
It will need to be replaced over time, but 20 or 30 feet will last quite a while.
Cable Welding Jig
A forum user (who goes by "Sherweld") posted directions on the Ornamental Turners International forum for a jig that makes it much easier to weld the cable into a continuous loop. The picture to the right shows the ends being held in this jig, and are shown just before they were melted and joined. Melting the ends to join them is done using a soldering iron.
I made one of these jigs from a scrap piece of walnut and parts I bought at the local hardware store. The metal parts cost less than $10.
I've used this a number of times, and it has never failed me.
Click here for instructions and more pictures: Cable Welding Jig
Examples of this device in use
- This YouTube video, MDF Rose Engine Lathe : #7 - Overhead drive, is a quick overview of the overhead drive I had on my original MDF Rose Engine Lathe.
- This YouTube video, MDF Rose Engine Lathe 2.0 - Overhead Drive, is a quick overview of the overhead drive I now use on my original MDF Rose Engine Lathe 2.0.
Usage Notes
The overhead drive should be adjusted so that the drive cable has as vertical alignment as possible. The overhead drive cable is shown in the picture to the right in pink.
This only shows the view from the inboard side, but the alignment when viewed from the near side should be similarly aligned. In that case, the cable should be vertical when halfway thru the movement along the Z axis. So, it you are planning to move the cutting frame 2", then at 1", it should be vertical.
The last thing to check is that the tension on the overhead cable is right.
- Too much is not good, especially if you use the piston-style quick-change tool post as it can pull the cutting frame or drilling spindle up. (And, this will always happen at the worst possible time, destroying many hours of work.)
- Too little is also not good as it can allow the drive cable to "flop around" creating too much vibration in the cutting.
- This is also the reason you should keep the vertical distance short. Reduce the length of the cable if needed.
Notes on making one
Static can build up from the overhead drive belt much like the belt does on a Van de Graaff generator. This can be alleviated by attaching a brush with brass bristles so that the bristles just barely graze the belt, and those bristles are also connected to an earth ground. An example of one is shown in the picture to the right.
It should be noted that the brush needs to have brass bristles. Plastic ones will not work, and stainless steel ones are typically too stiff and are more prone to causing premature wear of the drive belt.
As mentioned, the wire shown in the picture to the right is connected to an earth ground. Mine is wired via the ground pin on an electrical plug. Others in the USA have told me they do the same, however you will need to ensure your electrical code requirement where you live.
Note 1: It is a good practice to bond this grounding to the base for the machine also (on the MDF Rose Engine Lathe, bond to the metal plate on the top).
Note 2: Some have mentioned that certain types of drive belts do not accumulate static electricity as much as others. I have no experience with this, and can only add that grounding the wires as mentioned is a good practice.
More Information
Published Articles
- Build an Overhead Drive, by Jon Magill. American Association of Woodturning's magazine, "American Woodturner", Spring 2008, pg 30.
Disclaimer: eMail comments to me at OTBookOfKnowledge @ Gmail.com. The process of woodturning involves the use of tools, machinery and materials which could cause injury or be a health hazard unless proper precautions are taken, including the wearing of appropriate protective equipment. |